HONEYWELL | 05701-A-0288 | Function card
System 57 operates on a rated 24V (18V to 32V) DC power supply and can obtain supply inputs from various sources, including mains AC power, through a separate AC to DC power supply device, local factory DC power supply, and/or battery backup DC power supply. The power supply is provided to the system through a DC input card 57
It provides a terminal block that allows for flexible power connections and diode separation for two independent power inputs. The required rated power depends on the type and quantity of sensors, channels, and configuration of system 57. The following power budget calculation table allows for quick and simple calculation of the worst-case power requirements of the system. In many cases, however, a more detailed power budget should be analyzed to confirm the exact requirements. The 8-way AC to DC power supply unit can provide either 50W DC power or 100W DC power, depending on whether it is in single switch mode or dual switch mode, and the module is included in the power supply unit. Similarly, 16 AC to DC power units can provide 50W, 100W, 150W, and 200W DC power, depending on whether one, two, three, or four switch mode module power units are included.
Many products have not been listed yet. For more products, please contact us
If the product model is inconsistent with the displayed image, the model shall prevail. Please contact us for specific product images, and we will arrange for photos to be taken and confirmed in the warehouse
We have 16 shared warehouses worldwide, so sometimes it may take several hours to accurately return to you. We apologize for any inconvenience caused. Of course, we will respond to your concerns as soon as possible.
05701-A-0288 Other
names:
Input/output module 05701-A-0288
05701-A-0288 Control Module
Analog module 05701-A-0288
The
5701 Single Channel Control Card provides control, display and alarm facilities
for a connected gas detector. The front panel display indicates the gas reading
and channel status while LEDs are used for alarms. A push-button is provided for
resetting the alarms and selecting the card for use with the Engineering
Card.
The operation of the control card is microprocessor controlled and is fully definable for a wide range of connected gas detectors and application requirements. The software configuration setup is stored in an EEPROM.
There
are two types of control card depending on the type of gas detector being fitted
to the system:
a. Single Channel Control Card 4 - 20mA. Part Number 05701-A-0301.
b. Single Channel Control Card Catalytic. Part Number 05701-A-0302.
Each of the above control cards consist of a single channel control card fitted with the respective plug-in sensor drive module.
An optional Analogue Output Module can also be plugged into the single channel control card to provide a remote output of the channel card readings.
Single
Channel Control Card
The
Single Channel Control Card carries out the control functions for a single loop
of gas detection as follows:
a. Processes the incoming sensor drive module signal.
b. Displays the signal level on the front panel liquid crystal display.
c. Compares the signal level with pre-defined alarm limits.
d. When the pre-defined alarm limits are exceeded, raises the alarms by lighting up front panel LEDs and operating optional connected relays.
e. Informs other cards with the alarm status information.
f. Self validates the operation of its circuit components, software operation and the condition of the sensor
Sensor
Drive Modules
Two
sensor drive modules are provided:
a. Sensor Drive Module, 4 - 20mA, Part Number 05701-A-0283
b. Sensor Drive Module Catalytic, Part Number 05701-A-0284
The Sensor Drive Module conditions the incoming catalytic or 4 - 20mA sensor signal and provides the necessary sensor power supply. It contains all the circuitry necessary to generate the voltages and currents required to drive the sensor, the circuitry to acquire the sensor signal and to scale the sensor signal to a standard output. The sensor drive modules are factory fitted and plug directly onto the channel control card.
Analogue
Output Module
An optional Analogue Output Module, (Part Number 05701-A-0285), may be factory fitted to the Single Channel Control Card and is used on a channel of gas detection to provide an isolated current loop output which follows the sensor signal level. This may be set electronically to produce a 0 - 20mA output or a 4 - 20mA output and can be used to operate a chart recorder, etc.
Single Channel Control Card Physical Layout
The physical layout of the Single Channel Control Card is shown below. The Sensor Drive Modules plug into the 14-way connectors J1 and J2 while the Analogue Output Module, when fitted, plugs into J3 and J4. Link LK1, available on MkII cards only, is used when individually powering control cards See Chapter 4, Section 16.2.
SYSTEM DESCRIPTION
Provides connections between the sensor and the control card in the same way as the Field Interface Card. This card is used to provide master alarm functions or a mixture of master and individual alarms. The card is fitted with eight relays, seven of which are fully configurable while the eighth is used for fault alarm. The relay states are monitored by the control card to ensure correct operation of the relays. In the case of a malfunction, the fault relay of the high integrity relay card de-energises. The fault relay shall always be monitored in order to ensure correct operation of the system.
All products on this website are special
products, and market prices have been fluctuating,
The specific customer service quotation shall prevail, as the product is a new one and the traps are not real,
Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,
New for sale, please contact the website https://www.axcontroler.com/ Customer service communication.
Recommended spare parts:
HONEYWELL
05701-A-0145
HONEYWELL
05701-A-0282
HONEYWELL
05701-A-0301
HONEYWELL
05701-A-0302
HONEYWELL
05701-A-0325
HONEYWELL
05701-A-0326
HONEYWELL
05701-A-0330
HONEYWELL
05701-A-0351
HONEYWELL
05701-A-0361
HONEYWELL
05701-A-0511
HONEYWELL
05701-A-0550
Honeywell
05704-A-0131
Honeywell
05704-A-0121
Honeywell
05074-A-0122
HONEYWELL
MP-DNCF02-200
PRODUCT TAGS
Shanxi Runsheng Import and Export Co., Ltd
Address: 3301, Building A, Wanda Center, No. 175 Jiefang Road, Xinghualing District, Taiyuan City, Shanxi Province
Google email: wkcarshop666888@gmail.com
Industrial Control Sales Consultant: Amelia
Whatsapp: +86 18030295882