IC698CPE040 GE Fanuc RX7i redundant memory module-Shanxi Runsheng

Your current location: Home - Product - GE

IC698CPE040 GE Fanuc RX7i redundant memory module

The purpose of a module is to operate as a node on a reflective memory network or as a specific link connecting two CPUs in a redundant system. It is compatible with the 5565 series storage devices and can determine the amount of data shared between PLCs and other computing devices. Each node in the GE Fanuc Automation redundant memory switching module is connected using fiber optic cables in a daisy chain loop mechanism. This connection method includes connecting the first node to the second node, then connecting the transmitter of the second node to the receiver of the third node, and so on, until the loop is connected to the first node and the loop is finally completed.

Contact Us

PRODUCT TAGS

Digital Output Module

Digital Quantity Module

Editable Controller

Electric General Gas Turbine Card

Electric Machinery

Excitation Control Module

Excitation System Controller

Programmable Controller

Program Module

Redundant System

Robot Spare Parts

Shipbuilding Industry

Ship Controller

Steel Works

Description

　　Many products have not yet been launched, please contact us for more products

　　If the product model does not match the displayed image, the model shall prevail. Please contact us for specific product images, and we will arrange for photos to be taken in the warehouse for confirmation

　　We have 16 shared warehouses worldwide, so sometimes it may take several hours to accurately return to you. We apologize for any inconvenience caused. Of course, we will respond to your concerns as soon as possible.

　　IC698CPE040 Other names:

　　Controller module IC698CPE040

　　IC698CPE040 Input/Output Module

　　Digital quantity module IC698CPE040

　　IC698CPE040 communication unit

　　Product Description

　　GE Fanuc's IC698CPE040 is a 16MB redundant memory switch used for the Rx7I Pacsystem. Its dimensions are as follows: 6.299 inches wide x 9.187 inches high. It has 16MB of SDRAM user memory. The working voltage of the power supply is+5 V DC. The current requirement is 1.8A. The device has fiber optic LC type connectors and zirconium ceramic ferrules that comply with IEC 61754-20. The maximum insertion loss is 0.35 dB, and the return loss is -30dB. The acceptable temperature range is -20 ° C to+85 ° C. To complete the installation, you need to ensure that you have all of the following items: PACSystems RX7i CPU with firmware version 2.00 or higher; PACSystems Rx7i CPU rack with power supply; PC compatible computer with CIMPLICITY Machine Edition - Logic Developer PLC, version 4.5 or higher programming software, and necessary cables.

　　Please note that in order to meet radiation emission standards, RX7i systems containing multiple Memory Xchange modules must be installed in conductive metal enclosures or equivalent environments. The memory module should only be installed in RX7i rack 0 (main rack). Suggest installing the RMX module in slots 4 and 3 of the mainframe. This provides VME interrupt request priority for the RMX module. Although this configuration is recommended, it is not strictly required to install the RMX module in slots 4 and 3. To install the IC698CPE040 redundant memory switch, please ensure that the rack power is turned off. Next, slide the module into the accurately configured slot in the system. Continue to press the circuit board into place, but do not apply force. Tighten the screws at the top and bottom of the panel. Next, make sure to connect the cables to the RX and TX connectors. Fiber optic cables should be routed from the TX connector to the RX connector of the next node. Connect the TX cable of the board to the RX connector of the next node. Repeat this operation until the last node in the ring wires its TX to the RX connector of the first node. Turn on the power.

　　IC698CPE040 was initially in an unconfigured state, at which point its light emitter was disabled. The redundant memory swapping module will not run on the network until the RX7i CPU sends the hardware configuration to the module. To achieve reflective memory operations, users can choose to configure the following parameters: redundant transfer mode, node ID, network memory offset, Rogue Master, and interrupt enable. Please note that if redundant link operation is selected, the above parameters will be set by the CPU and therefore cannot be configured. Please note that when IC698CPE040 is used as a general-purpose reflective memory module, user logic can perform additional functions beyond basic read and write operations, including reading interrupt states, enabling interrupts, reading parity errors, and enabling parity.

　　The IC698CPE040 redundant memory swapping module belongs to the RX7i PACSystems series of GE Fanuc Automation. The purpose of this module is to run as a node on a reflective memory network or as a specific link connecting two CPUs in a redundant system. It is compatible with 5565 series memory devices and can determine the amount of data shared between PLCs and other computing devices. Each node in the GE Fanuc Automation IIC698CPE040 redundant memory switching module is connected using fiber optic cables in a daisy chain loop mechanism. This connection method includes connecting the first node to the second node, then connecting the transmitter of the second node to the receiver of the third node, and so on, until the loop is connected to the first node and the loop is finally completed.

　　The GE Fanuc Automation IC698CPE040 redundant memory swapping module is designed to be installed in a single slot of the RX7i PACSystems rack. It has a reflective memory capacity of 16 MB and software configuration is executed for old node parameters in preparation for new applications. In addition to all these features, this module also has network compatibility with VMIC 5565 reflective memory devices and can be connected to them through multimode fiber optic cables up to 300 meters in length. Some of the accessories included in this catalog for use with the GE Fanuc Automation IC698CPE040 redundant memory swap module include redundant memory modules, control memory modules, fiber optic swap cables, lithium battery pack rack fan components, and different power supplies that can be used with this module to enhance its functionality.

　　All products on this website are special products, and market prices have been fluctuating,

　　Please refer to the customer service quotation for details, as the product is new and the price is not genuine,

　　Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,

　　The new one is for sale, please contact customer service for further communication.

Previous: None

Next: None