Many products have not yet been launched, please contact us for more products

　　If the product model does not match the displayed image, the model shall prevail. Please contact us for specific product images, and we will arrange for photos to be taken in the warehouse for confirmation

　　We have 16 shared warehouses worldwide, so sometimes it may take several hours to accurately return to you. We apologize for any inconvenience caused. Of course, we will respond to your concerns as soon as possible.

　　DS200UDSAG1ADE - Analog I/O Board is available in stock which ships the same day.

　　DS200UDSAG1ADE - Analog I/O Board comes in UNUSED as well as REBUILT condition.

　　DS200UDSAG1ADE is an analog I/O board manufactured and designed by General Electric, belonging to the Mark V LM series used in turbine control systems. The Analog I/O Board (TCQA) can scale and adjust the large number of analog signals read by the terminal boards installed on the I/O cores R1, R2, and R3. This signal group includes LVDT input, servo valve output, thermocouple input, 4-20 mA input and output, vibration input, relay driver output, pulse input, voltage input, as well as generator and line signals. On the STCA board, some signals are written through 3PL connectors. Through JE connectors, the TCQC board receives and transmits generator and line signals. The TCQA board can scale and adjust the input signal of 420 mA, including fuel flow pressure and compressor stall detection signal.

　　TCQA connector:

　　2PL - distributes power from TCPS board to, and from the core.

　　3PL - The data bus between the STCA, TCQA, and TCQE boards in the core, as well as between the STCA, TCQA, and TCQE boards in the core. In order to transmit to COREBUS, conditionally adjusted signals are transmitted over 3PL.

　　JA - Connect JAR/S/T from TBQA board to carry corresponding R1, R2, and R3 core thermocouple inputs and cold junction calibration.

　　JB - Supports 4-20 mA input and output connected to the JBR terminal board on TBQC.

　　JD - Transmit the trip signal from the R1 core to the TCTG board in the P1 core; Not used in R2 or R3.

　　TCQA configuration:

　　Hardware: Use hardware jumpers J1 and J2 to select the mA output circuit. Use J5 and J6 to configure the mA output current range (maximum 20 mA or maximum 200 mA). For card testing, connect the RS232 port to J7. The oscillator is activated by J8. For detailed information on the hardware jumper settings for this board, please refer to Appendix A and the hardware jumper panel in the operator interface.

　　Software: The following introduces how to input 4-20 mA input and output, vibration, LVDT position, pulse rate, and thermocouple I/O configuration constants in the I/O configuration editor of the operator interface.

　　The Mark V turbine control system series is a traditional series because its original manufacturer is no longer actively producing it. That being said, the Mark V series is also one of the last product lines in General Electric's product line to adopt Speedtronic technology in its products, which was first introduced in the late 1960s along with the release of the Mark I. This DS200UDSAG1ADE PCB can be better defined as a circuit board with firmware; This is the original functional product description mentioned in the General Electric manual. This DDS200UDSAG1ADEcircuit board with firmware is not the original product with the expected functionality in the Mark V series; That should be the DS215TCQAG1 mother printed circuit board.

　　Hardware tips and specifications

　　This firmware equipped DS200UDSAG1ADE circuit board utilizes its own specific set of features to introduce hardware components and component specifications. The GE RST analog I/O board DS200TCQAG1 includes six 34 pin connectors, two 40 pin connectors, and six jumpers. The board also has 6 LEDs. The LEDs are arranged in two rows, with three LEDs in each row, emitting light to indicate various functional faults or diagnostic test status. When the DS200UDSAG1ADE board is installed in a larger Mark V series drive, it is installed between other boards, and the side of the GE RST analog I/O board DS200TCQAG1 is visible from the front glass of the cabinet. The LEDs in this DS200UDSAG1ADE PCB assembly are arranged so that the operator can see them while the driver is running. The LED indicates the operational status of six functions on the circuit board and flashes when an activity occurs. To understand the purpose of each LED, you can read the installation instructions provided by the factory with the original circuit board for information about the LED. The driver operator can easily determine the operating status and ongoing processing of the circuit board at a glance.

　　JA, JB, JD, JE, JG, and 3PL are the IDs assigned to the 34 pin connector in the assembly of this DS200UDSAG1ADE circuit board (with firmware). The ID is printed on the surface of the circuit board next to each connector. When you plan to replace a circuit board, please check the faulty circuit board while it is in the driver and mark the ID of the connector it is connected to on the ribbon cable. This will accelerate the installation speed of the new circuit board, as you will immediately know where to connect the 34 pin ribbon cable. Grasp the ribbon cable connector connected to the circuit board to remove it. It is important to understand the differences between this DS200UDSAG1ADE product and other common Mark V turbine control system series products before making the final purchase decision. Firstly, this DS200UDSAG1ADE PCB has a special Mark V series assembly version, which can be seen from the position of the special DS215 series label in the DS200UDSAG1ADE functional product number. This firmware equipped DS200UDSAG1ADE circuit board not only has a special assembly version, but also comes with an optional Mark V series software package, which can be clearly seen from the official feature description of this DS200UDSAG1ADE PCB and the ZZ01A label at the end of the DDS200UDSAG1ADE feature product number.

　　Pulse rate input circuit:

　　The TCQA board contains circuits for scaling and adjusting the pulse rate input read from the TCQC board through JE connectors. These signals come from magnetic pickup inputs and TTL (transistor to transistor logic) inputs, which are sent to QTBA and/or PTBA terminal boards. The input of high-pressure shaft speed enters the "R1" core. Other signals can be used with pulse rate input circuits on R2 and R3.

　　TCQA 4-20 mA input circuit:

　　The circuits for 0-1 mA and 4-20 mA input signals are provided by the TCQA board. The signal is read from the TBQC terminal board through the JB connector. When the sensor current passes through the load resistor, the voltage drop is measured by the TCQA board and written to the I/O engine through the 3PL connector. The current range of the input signal is selected using the hardware jumper on the TBQC terminal board.

　　TCQA 4-20 mA output circuit:

　　The circuit that drives the 4-20 mA output to the TBQC terminal board through the JB connector is provided by the TCQA board. Usually, these signals are used to power control devices.

　　TCQA thermocouple circuit:

　　TBQA terminal board is coupled with thermocouple. The thermocouple cold junction reference is provided by the circuit also located on the TBQA terminal board, and TCQA uses this reference to calculate cold junction compensation. The actual temperature read by the thermocouple is determined by the TCQA board using thermocouple input and compensation settings. The value is read by the I/O engine through a 3PL connector. I/O configuration constants are used to select the type and curve of thermocouples.

　　Frequently Asked Questions

　　What input formats can DS200UDSAG1ADE read?

　　LVDT input is read by TCQA. A dedicated ribbon line connects the analog input-output board in the R control processor to the first redundant sensor input of VDC1 and VDC2.

　　What regulators are included in TCQA software?

　　The input/output setting software on the TCQA of each control processor in Mark V includes a digital control regulator.

　　What types of inputs does DS200UDSAG1ADE read?

　　DS200UDSAG1ADE reads LVDT input. The first redundant sensor input of VDC1 and VDC2 is also transmitted to DS200UDSAG1ADE in thecontrol processor through a dedicated ribbon cable.

　　What is a part of the DS200UDSAG1ADE software?

　　The digital control regulator is part of the I/O configuration software on the DS200UDSAG1ADE in each control processor of the Mark V.

　　What happens to DS200UDSAG1ADE when Mark V malfunctions and commits suicide?

　　When current fault suicide is enabled on the Mark V, the relay on DS200UDSAG1ADE will be de energized, and a pair of normally closed contacts on DS200UDSAG1ADE will short-circuit the output terminals together.

　　All products on this website are special products, and market prices have been fluctuating,

　　Please refer to the customer service quotation for details, as the product is new and the price is not genuine,

　　Please confirm the model, product, price, and other detailed information with customer service before placing an order. The website has been used,

　　The new one is for sale, please contact customer service for further communication.

Related product recommendations:
GE ENK32
EPSCPE100-ABAC
GE ESM10A
GE ESP10B
EVMECNTM13
EVPBDP032
EVPBDP0001
GE EX2100
HE693THM884
IC300DQM406A
HE693THM440E
HE693THM884L
HE693PBM101F
HE693THM666C
HE5000CS110-J
HE693STP104-PL3
HE693THM889B
HE693IBS100E
HE693THM668E
HE693RTD720E
HE693STP301E
HE693ADC816C
F650-FEEDERFMOD36-04
HE693DAC410
more......